Whole-Home Generac Standby Generators
Natural gas or LP, sized from the home's calculated and selected backup loads.
Whole-home standby generators, automatic transfer switches, and maintenance across the OKC Metro Area. Call or book online to plan a permitted install sized for your home.
Spark Shark Electric in Moore, Oklahoma installs whole-home Generac standby generators for OKC Metro Area homeowners. Ice, severe storms, and other grid events can interrupt power with little warning. A properly designed standby system detects a utility outage, starts the generator, and transfers the connected loads according to the equipment's sequence. We size the system from the loads you want available, install the automatic transfer equipment, coordinate required permits and trade work, and commission the system to the manufacturer's requirements.
Natural gas or LP, sized from the home's calculated and selected backup loads.
Detect a utility outage and transfer the connected loads according to the system's programmed sequence.
Optional, for homes where running everything at once would oversize the unit.
See status and run history from your phone.
Oil change, filter, exercise-mode test, transfer-switch verification.
Every home has different wiring, load demands, access, and code requirements. Spark Shark Electric keeps the visit focused on the actual problem, the available options, and the written scope before work begins.
Can damage utility equipment and interrupt service across the OKC Metro Area.
Can last longer than a homeowner expects even when nearby neighborhoods have power.
Can make an outage more disruptive for households that rely on powered heating, cooling, refrigeration, or medical equipment.
May include selected HVAC equipment, refrigeration, pumps, lighting, internet, or other priorities when the generator and fuel system are sized for them.
We look at your service size, the breakers you actually use, and which loads matter when the power's out.
HVAC, fridge/freezer, kitchen, lighting, internet come first.
Electric vehicle charging, pool equipment, large workshops are layered in or load-managed.
A too-large generator costs more, uses more fuel, and runs less efficiently.
Generator pad set, gas line tied in by a licensed plumber (we coordinate), ATS wired into your panel.
Required startup, transfer, load, and control checks based on the installed equipment and manufacturer instructions.
Monitoring, exercise schedule, and what to expect during the next outage.
Permit pulled on every install, inspection scheduled.
A generator install often pairs with a panel upgrade. Spark Shark Electric handles both, and we'll cross-quote the panel and the generator in a single written estimate so you can plan the project once.
Standby generators need electrical work, gas planning, utility requirements, permits, and inspection timing coordinated before install day.
After commissioning, we walk through transfer behavior, exercise schedule, monitoring, and what to check after the first outage.
Keeps the unit ready for the day it actually has to run. We offer maintenance plans on units we install.
A good standby generator quote depends on what you want powered, available gas capacity, ATS location, panel condition, and permit requirements. We size the system before writing the number.
We coordinate the electrical scope and required licensed trade partners before install.Call if an outage or unsafe generator setup is happening now.
Book a generator site visit for sizing and quote planning.
Learn what to watch for, what is safe to check, and when to call a licensed electrician.
Runtime depends on the generator's actual load, fuel supply, maintenance needs, weather, and equipment limits. Natural gas service can also be interrupted, and usable LP capacity is lower than the tank's nameplate volume. We size fuel needs for the proposed system rather than promising a universal runtime.
Permit and inspection requirements depend on the jurisdiction and the electrical, gas, and site-work scope. We confirm the requirements for the property and coordinate the applicable permits and inspections.
Sound ratings and measurement distances vary by model and operating load. We use the selected unit's published specifications and the applicable siting rules when planning placement.
It depends on generator size, gas-line work, ATS complexity, panel modifications, and any pad/site prep needed. After an on-site assessment, we give you a written up front quote with the required scope and charges disclosed before work begins.
Sometimes, but not automatically. We inspect the panel, transfer-equipment arrangement, selected backup loads, and service configuration before recommending any panel work.
Residential electrical service throughout the OKC Metro Area.
In The Dark? Call The Shark!
Up front, written pricing. Licensed Oklahoma electricians. Live 24/7 phone for emergencies.